Wheels

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - One 264mm spoke = 6g - Nipples sold separately

DT Swiss Sinc Ceramic cartridge bearings. - The black dust cover is intended to be installed facing the hub and the tan seal is intended to face externally

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding. - The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry. - No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.

You like gravel and wide tires? This is your rim. The GR 531 is made for off-road adventures. This aluminum gravel rim with an inner width of 24mm is designed for wide, knobby tires up to 53mm. Torsion-resistant and robust, the welded rim supports a wide range of gravel use.

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum

Tannus Armour Tubeless inserts are the result of years of top level multi-cell foam manufacturing mixed with extensive professional riding experience. At the heart of Tannus is the patented Aither Technology; a multi-cell foam compound that forms the structure of the Armour. The inserts are designed to displace small impacts while offering a spring-like rebound for a smooth yet playful ride. - 3% Faster than standard tubeless - Flexible sidewall stabilizing "Wings" for smoother ride quality, with 50% more vibration damping - 20mm of rim protection - Not a sealant sponge – keeps sealant where it belongs - Easy Installation (5 Minutes, No tools required) - 150g - About as much as a standard tube (a little lighter)

Grade 10 chromium steel balls

- Zipp’s ultimate road racing wheelset. Aerodynamically efficient and stable in all wind conditions. - Optimized for 28mm tubeless tires at lower pressure for reduced rolling resistance and vibration damping. - Total System Efficiency (TSE) approach addresses wind resistance, gravity, rolling resistance, and vibration losses. - More than 400 grams lighter than its predecessor - Hookless rims for a more seamless and aerodynamic transition between tire and the rim - Cognition V2 Hubset with an updated Axial Clutch V2 mechanism for quicker engagement, lower friction, and improved durability. - Center locking rotor interface. Lockring is included with the wheels - 1360g - Lifetime warranty

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

- Zipp's most advanced and fastest deep-rim wheel for road, triathlon, and time trialing - More than 300 grams lighter that previous model - Optimized tire bed for easy tire installation - Sawtooth rim with Hyperfoil nodes and HexFin ABLC dimple pattern for top aero and crosswind-stability performance with an undulating rim depth - Cognition V2 hubset rolls efficiently whether you are pedaling or coasting. Its Axial Clutch V2 technology reduces drag and lowers friction - Center locking rotor interface. Lockring is included with the wheels - Zipp graphics applied using Zipp's ImPress direct-print technology - Minimum 25mm tire width - Lifetime Warranty

Industry Nine Hydra Classic hubs are the heart of your wheelset, everything revolves around them, literally. Every Classic Hydra hub is made start to finish in Asheville, NC. From turning and milling bar stock 7075-T6 aluminum for shells, axles and encaps, wire EDM cutting A2 tool steel for pawls and driverings, to in-house anodization lab, every step of design, engineering, manufacturing and assembly is done to exacting standards. - 690 P.O.E. Hydra Freehub body engages every .52 degrees yeilding telepathic control - 6 pawl, 6 phase - 115 tooth drivering - Easily serviced with no proprietary tools. Designed to keep you in the saddle and out of the service queue - Classic j-bend spoke interface - Steel cartridge bearings are durable

Small component with a large impact. A poorly constructed or unsuitable tyre rim tape can be the cause of many punctures. It is especially important with hollow section rims to use a pressure-resistant rim band which covers the entire rim. The fabric-reinforced Continental Easy Tape rim protector is designed for use under high air pressure conditions. The various widths enable a perfect fit for all standard rims. The high pressure design for racing cyclists withstands up to 220 psi, without becoming deformed. The flat construction type also significantly eases the job of tyre fitting.

Front axle conversion kits convert your hub to fit a new axle measurement or for a new group set.

Replacement freehub bodies for Vault hubs. - Use to replace worn/damaged freehub body or to switch cassette standards. - 60T

CX-Ray 298mm Straight pull spokes fit every position of the Rise 60 (B1), 29" wheel. - Length: 298mm - Spoke Interface: Straight Pull

Whether the goal is a finish line, epic adventure or simply getting back home again, our new 900 hubs are ready for the challenge. On the inside, our smooth and durable DOUBLE TIME drive mechanism ensures rapid lightning-fast engagement for quick and confident pedal responsiveness. SPEEDBALL bearings provide smooth, long-lasting rotation performance. Multiple spoke-count and cassette-capability options, as well as interchangeable end caps make the 900 hubs a perfect choice for any disc-equipped road, gravel, cyclocross, cross country, trail, or enduro bike. - Includes Quick Release & 12x142mm Through AxleCaps - Fully convertible with tool free end caps - DOUBLE TIME mechanism offers smooth,quick and durable engagement - Versatile driver body can accept ROAD or MTB drivetrain, full spline or XD cassettes - Axle type: Conversion Caps included - Spoke holes: 24 - Brake compatibility: Disc (6-bolt) - Driver Mechanism: Double Time - Four Pawl - Axle material: Tapered aluminum - Driver body material: Aluminum - Hub shell: Aluminum - Seeker angled flanges - Oversized body

SRAM's 506 hub borrows technology from its more expensive brethren to bring you a solid hub at a great price. An aluminum hubshell with hi/lo flanges provide no-nonsense durability and even spoke tension. Dependable cup and cone bearings with polished races roll smooth for the long haul and a strong, steel quick-release axle holds up under pressure.

SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.

Whether the goal is a finish line, epic adventure or simply getting back home again, SRAM'S 900 hubs are ready for the challenge. On the inside, the smooth and durable DOUBLE TIME drive mechanism ensures rapid engagement for quick and confident pedal responsiveness. SPEEDBALL bearings provide smooth, long-lasting rotation performance. Multiple spoke-count and cassette-capability options, as well as interchangeable end caps, make the 900 hubs a perfect choice for any disc-equipped road, gravel, cyclocross, cross country, trail, or enduro bike. - Versatile driver body can accept ROAD or MTB drivetrain, full spline or XD cassettes - Fully convertible with tool-free end caps - BOOST variants - 24, 28 or 32 spoke holes

Heavy duty and extra wide PVC rim strips for maximum tube protection.

Shimano Dura-Ace 9000 Hub Quick Release Skewer. - Axle Type: Standard QR

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many BMX hubs - Type: Solid Axle - Threads: 9.5mm x 24tpi - Diameter: 9.5mm - Length: 180mm - 1 axle per bag

The Problem Solvers Axle Nut is perfect for wheels with solid axles (also called bolt-on axles). This quality nut is made of durable chrome-plated steel and features a built-in integrated rotating washer to hold tight.

The number to count on—240 with Ratchet EXP. The new 240 is developed for riders with the most extreme ambitions. The latest version of the hub is equipped with the Ratchet EXP system to maximize reliability. The increased bearing distance increases bearing lifetime, the straight spring provides more direct engagement (which reduces wear), and a smaller number of parts not only makes maintenance easier, but also reduces weight.

This sleeved, 25mm-wide, light, and strong rim is as versatile as AM riding itself. Derived from our extremely successful Enduro rims, which have won at the world's highest level under the world's fastest racers, the M 462 packs that world-class technology into a slightly slimmed package for All Mountain use while staying affordable thanks to the sleeved rim joint.

Direct power meets simplicity—running smoothly day-in and day-out. The 350 hub was developed according to the credo: Reliability meets simplicity. The simultaneous engagement of the ratchets and the resulting large engagement area provide reliability. The plugged construction allows easy maintenance without the need for tools. Adaptation to different axle standards or modification of the engagement angle is also possible with just a few manual steps.

When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever. - Ratcheting system tightens skewers with turns rather than a cam - Lever can be rotated into an ideal position after tightening - Removable, plug-in lever design is streamlined and protects your RWS lever